TEKSUN PROCESS

End-to-End Product Development & Project Fulfillment

Teksun's New Product Introduction Process

Here is Teksun’s established New Product Introduction Life Cycle, meticulously designed to encompass every crucial stage from conceptualization to commercialization. At every step of this journey, Teksun stands ready to provide unwavering support and guidance.

Phase 1

PLAN & DEFINE PROGRAM

Phase 2

PRODUCT DESIGN & DEVELOPMENT

Phase 3

PROCESS DESIGN & DEVELOPMENT

Phase 4

PRODUCT & PROCESS VALIDATION

Phase 5

FEEDBACK, ASSESSMENT & CORRECTIVE ACTION

Key Activities :

Customer SOR/ RFQ
Review of customer inputs/ drawings and samples.
Team feasibility commitment review complete and go ahead received from CFT.
Risk analysis review complete and go ahead received from CFT.
CFT declaration
Design goals reviewed.
Reliability & quality goals reviewed
Preliminary bill of material for costing
Preliminary process flow diagram for costing
Concept 2D/3D part drawing for costing.
Equipment Planning
Equipment specification cost planning Product Design Development

Key Activities :

Customer Go ahead for development
APQP Timing Plan preparation and review
Review of input and output parameters
2D/3D drawings review
Part List preparation post defining selection criteria & Components Arrangement
Proto sample preparation & Testing
Design verification Testing
DFMEA Preparation
Proto control Plan preparation
Updation of Design Poka-Yoke
Bench marking report review if benchmark sample available
Submission of proto samples to customer
Customer Loodback

Key Activities :

Equipment, Tester & Fixture concept & detail design development & manufacturing.
Check & implement applicable MP info sheet.
Completion of sample inspection report for tooled-up part
PFMEA PFC,C PMSA & Process capability review
Pre-production trial run
Tool Validation Report
Identification and review of critical processes
Review and finalization of packaging standard

Key Activities :

Durability Test Review
Production Trial run review
Process capability review
PPAP Document review
Packaging evaluation review
Control Plan Review
PFMEA Review
DFMEA Review
Arrangement of Components for Pilot lot production.
Equipment trail at manufacturer site
Equipment Installation

Key Activities :

Pilot lot submission with PPAP documents
Customer Feedback review
Review of Design document if required
Undation of Lesson Learnt history
Undation of design Records
Undation of product development history
Quality Planning Sign-off
Start of production
Equipment initial phase production flow

Phase 1

PLAN & DEFINE PROGRAM

Key Activities :

Customer SOR/ RFQ
Review of customer inputs/ drawings and samples.
Team feasibility commitment review complete and go ahead received from CFT.
Risk analysis review complete and go ahead received from CFT.
CFT declaration
Design goals reviewed.
Reliability & quality goals reviewed
Preliminary bill of material for costing
Preliminary process flow diagram for costing
Concept 2D/3D part drawing for costing.
Equipment Planning
Equipment specification cost planning Product Design Development

Phase 2

PRODUCT DESIGN & DEVELOPMENT

Key Activities :

Customer Go ahead for development
APQP Timing Plan preparation and review
Review of input and output parameters
2D/3D drawings review
Part List preparation post defining selection criteria & Components Arrangement
Proto sample preparation & Testing
Design verification Testing
DFMEA Preparation
Proto control Plan preparation
Updation of Design Poka-Yoke
Bench marking report review if benchmark sample available
Submission of proto samples to customer
Customer Loodback

Phase 3

PROCESS DESIGN & DEVELOPMENT

Key Activities :

Equipment, Tester & Fixture concept & detail design development & manufacturing.
Check & implement applicable MP info sheet.
Completion of sample inspection report for tooled-up part
PFMEA PFC,C PMSA & Process capability review
Pre-production trial run
Tool Validation Report
Identification and review of critical processes
Review and finalization of packaging standard

Phase 4

PRODUCT & PROCESS VALIDATION

Key Activities :

Durability Test Review
Production Trial run review
Process capability review
PPAP Document review
Packaging evaluation review
Control Plan Review
PFMEA Review
DFMEA Review
Arrangement of Components for Pilot lot production.
Equipment trail at manufacturer site
Equipment Installation

Phase 5

FEEDBACK, ASSESSMENT & CORRECTIVE ACTION

Key Activities :

Pilot lot submission with PPAP documents
Customer Feedback review
Review of Design document if required
Undation of Lesson Learnt history
Undation of design Records
Undation of product development history
Quality Planning Sign-off
Start of production
Equipment initial phase production flow

RFQ to FDR- Teksun Project Delivery Cycle

Below you will discover the various stages of your Project’s Delivery Cycle, starting from a Request for Quotation (RFQ) which initiates
the Product Requirement Gathering process, and ending with a Final Delivery Report, which releases all final Project Deliverables.

01.